FAQs

• After installing the AM01 monitor arm, do I need to adjust the monitor’s tilt tension?

  If you are using the Studio Display, no additional tilt tension adjustment is required. The AM01 is factory-calibrated to the optimal tension value, so no further adjustments are necessary.

  Learn More

• How many cables can the cable slot, clips, and management box of the Studio Arm AM01 / AM02 hold at most?

  The following are the results of our internal testing. The actual number of cables the arm can accommodate depends primarily on the diameter of your cables:

  Rear Arm Cable Slot: Can hold up to 5 cables (e.g., 1 power cord with a 7.5mm diameter + 4 Type-C cables with a 5mm diameter).

  Base Cable Cover: Can hold up to 6 cables (e.g., 2 power cords with a 7.5mm diameter + 4 HDMI cables with a 6.5mm diameter).

  Cable Clips: Can hold up to 5 cables (e.g., 1 power cord with a 7.5mm diameter + 4 Type-C cables with a 5mm diameter).

  Learn More

• How can I assess whether my desktop environment and workspace are suitable for the use of the AM01/AM02?

  Desktop Material Restrictions: It is recommended to use solid wood, durable engineered wood, or metal desktops. Desktops made of glass, hollow core, or honeycomb structures are more fragile and, therefore, not suitable for monitor stand installation, as uneven stress may cause damage to the surface.

  Desk Edge Structure Restrictions: If the desk edge features a bevel or a large rounded corner exceeding 2.5 cm, the desk clamp may not secure properly. In such cases, a through-desk mounting method is advised.

  Under-Desk Clearance: If there are frames, crossbars, or partitions located too close to the desk edge underneath, the clamp may be obstructed and unable to fasten securely. Under these circumstances, a through-desk mounting solution is necessary.

  Supported Desktop Thickness: The AM01 and AM02 support desktop thicknesses—from 15 mm to 70 mm (0.59" to 2.76")—for both clamp and through-desk mounting options.

  Rear Clearance: If your desk is positioned flush against a wall with less than 11 cm of clearance between the desktop and the wall, the desk clamp may not fit properly. Additionally, please ensure sufficient space to accommodate the stand’s range of motion to prevent collisions with the wall when rotating or adjusting the monitor’s depth.

  Learn More

• What is the range of motion for adjustments on the AM01?

  Height adjustment range: 270 to 490 mm

  Forward and backward adjustment range: 100 to 413.5 mm

  Left and right adjustment range: +315 to -315 mm

  Monitor tilt adjustment range: 45° to -20°

  Monitor rotation (landscape/portrait) adjustment range: 90° to -90°

  Learn More

• How can I verify if my desktop material is suitable for the INFTYLAB Studio Arm AM01/AM02 series?

  If your desktop material is glass, hollow core board, honeycomb board, or MDF (medium-density fiberboard), the use of  Studio Arm is not recommended.

  Learn More

• After completing the installation of the AM01 monitor arm, is it necessary to adjust the weight support for the monitor?

  1. If you are using the VESA version of the Studio Display, no adjustments are required, allowing you to enjoy optimal operation.
  2. If you are using the Tilt Adjustable Stand version of the Studio Display, please adhere to the following instructions:
     2-1. Ensure that the Studio Display is securely mounted on the monitor arm.
     2-2. Lower the monitor to its lowest height, then continue applying downward pressure until a "click" sound is heard. Afterward, rotate the knob to the next position.

  Please note:
  The knob should only be rotated when the monitor is at its lowest position. Do not attempt to rotate the knob at any other height.

  Learn More

• What should I do if my monitor sags after installing a third-party brand?

  If the height is sagging:
  Please confirm that the total weight of all suspended items on the monitor arm falls within the range of 5.8–6.4 kg (12.79–14.11 lbs) or 8–8.6 kg (17.64–18.96 lbs). If the weight is outside these specific ranges, rising or sagging is a normal occurrence. Please return the arm to the sales platform where it was purchased within the return window authorized by your distributor.

  If the monitor tilt is sagging:
  Please confirm that the total weight of all suspended items on the monitor arm falls within the range of 5.8 kg–8.6 kg (12.79–18.96 lbs).
  If it meets this requirement, please use the Allen wrench provided inside the cable management box and adjust it according to the following instructions:

  Learn More

• How can I confirm if my iMac can be directly mounted on the AM02?

  How to confirm: Simply inspect the back of your monitor.

  VESA Adapter Version: There are four standard screw holes located in the center on the back. The AM02 fully supports both the 100x100mm and 75x75mm mounting patterns and can be directly mounted.

  Standard Stand Version (default stand): The original Apple stand cannot be detached, so the monitor cannot be directly mounted on the arm.

  Solution: Please contact Apple Support to inquire about replacing the stand with the VESA version, or purchase the dedicated SCS01F adapter for expansion and connection.

  Height-Adjustable Version: The original Apple stand cannot be detached, so the monitor cannot be directly mounted, and the SCS01F adapter is not compatible.

  Solution: Please contact Apple Support to inquire about replacing the stand with the VESA version.

  Learn More

• Are there any recommended cable lengths for cable management?

  The base cable management box is primarily designed to store peripheral cables and does not have any specific cable length requirements.
  For managing cables along the rear arm of the bracket:
  Taking the cables connected directly to the monitor as an example (e.g., if you have 4 Type-C cables), a length of 1.5 meters is recommended if you plan to move, extend, or adjust the height of the arm.

  Learn More

• Can I install the INFTYLAB Studio Arm with IKEA's table?

  The ANFALLARE and LAGKAPTEN series desks and workstations are compatible with the INFTYLAB Studio Arm.

  However, the INGO series dining and work tables are not suitable for use with the INFTYLAB Studio Arm.

  ANFALLARE series desks/workstations: Compatible for installation

  LAGKAPTEN series desks/workstations: Compatible for installation

  INGO series dining/work tables: Unfortunately, due to insufficient edge clearance, these are incompatible with the BenQ ERGO ARM gas spring monitor stand.

  Learn More